|
 |
Device Specifications
- neoVI 3G Architecture over 10x performance over previous devices
- 3 DSPs and 1 RISC processor for 125 MIPS of processing
- Power Consumption (typical) : 150mA @ 14.4 VDC
- Sleep Power Consumption (typical) : 12mA @ 12.0 VDC
- Power Supply: 5.5-27 Volt Power Operation
- Temperature Range: -40C to +85C
- Vehicle Connectors : 25 Pin male D-SUB and 9 Pin Male D-SUB
- Warranty: One Year Limited Warranty
- Firmware: Field upgradeable design (flash firmware)
- General Purpose IO: 6 MISC IO (0-5V on MISC 1-2 and 0 - 3.3V on MISC 3-6), 4 IO can be configured as analog
- General Purpose IO rate report interval: 1 Hz to 10 kHz or based on digital change
- General Purpose IO Maximum Current Output (Sunk/Sourced): 4mA
- Microsoft Certified USB drivers
- Isolated USB
- Stand-Alone Mode Including Scripting, Receive Messages, Transmit Messages,
- Expressions, IO, and Transport Layers
- ICS TimeSync for Multiple Hardware Synchronization supports all neoVI 3G devices
- neoVI FIRE: J2534 and RP1210 A/B compatible for CAN/ISO15765, Keyword, ISO9141, and J1850 VPW
neoVI RED: J2534 and RP1210 A/B compatible for CAN/ISO15765, Keyword, and ISO9141
- microSD card slot support up to 2 Gigabytes of storage. The removable card is formatted using FAT32 for direct usage in a PC.
- Battery backed real time clock (RTC)
Networks - General
- 64 Bit time stamping to accuracy of 10 microseconds on CAN and LIN networks and never overflows. 0.5 microsecond accuracy timestamp available if using one network only
- Simultaneous operations on all CAN/LIN/J1850 networks
- Transmit message double-buffering on all networks allows back to back message transmission
Network Specification
neoVI FIRE:
6x CAN Channels
- 4 Dedicated ISO11898 Dual Wire CAN Physical Layer (TJA1040)
- 1 Dedicated ISO11519 Low Speed Fault Tolerant CAN Physical Layer (TJA1054A)
- 1 Dedicated Single Wire CAN Physical Layer GMW3089 / SAE J2411 (MC33897)
- CAN 2.0B Active
- Up to 1 M-Bit Software Selectable Baud Rate (auto baud capable)
- Capable of generating and detecting error frames
- Logic Analysis of CAN Waveform with 25 nanosecond resolution
- Graphical Bit Time / Baud Rate Calculator
- Listen only mode support
- Unterminated network detection
- High Speed Mode, Test Tool Resistor, and High Voltage Wakeup support
4x LIN (Local Interconnect), ISO9141, Keyword 2000, or K and L Line
- Full support for LIN 1.X, 2.X and J2602
- LIN J2602 / 2.X compatible physical layer
- Software Selectable LIN Master Resistor
- Capable of Generating LIN Waveforms (Including Errors) Using Dedicated Output Compare Hardware
- UART Based State Machine
- Initialization Waveforms including Fast Init, Five Baud, and Custom
- Programmable Timing Parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution)
- Software Selectable Baud Rate
- LIN Bus Monitor Mode identifies errors : Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors.
- LIN Bus Master Mode operates at same time as LIN Bus Monitor
- LIN Bus Slave simulation - with or without an LDF file
- LIN Bus hardware schedule table with support for LIN diagnostics
1x J1850 VPW (GM Class 2)
- VPW Physical Layer capable of TX and RX operations in high speed modes (MC33390)
- Reception of IFR data during TX and RX
- Capable of high speed block programming
1x GM CGI
- Software Enabled (disables LIN2)
- Programmable Bit Rate
- Full block mode message reception only
neoVI RED:
2x CAN Channels
- 1 Dedicated ISO11898 Dual Wire CAN Physical Layer (TJA1040)
- 1 User Selectable ISO11898 Dual Wire CAN Physical Layer (TJA1040), SO11519 Low Speed Fault Tolerant CAN Physical Layer (TJA1054A), or Single Wire CAN Physical Layer GMW3089 / SAE J2411 (MC33897)
- CAN 2.0B Active
- Up to 1 M-Bit Software Selectable Baud Rate (auto baud capable)
- Capable of generating and detecting error frames
- Logic Analysis of CAN Waveform with 25 nanosecond resolution
- Graphical Bit Time / Baud Rate Calculator
- Listen only mode support
- Unterminated network detection
- High Speed Mode, Test Tool Resistor, and High Voltage Wakeup support
2x LIN (Local Interconnect), ISO9141, Keyword 2000, or K and L Line
- Full support for LIN 1.X, 2.X and J2602
- LIN J2602 / 2.X compatible physical layer
- Software Selectable LIN Master Resistor
- Capable of Generating LIN Waveforms (Including Errors) Using Dedicated Output Compare Hardware
- UART Based State Machine
- Initialization Waveforms including Fast Init, Five Baud, and Custom
- Programmable Timing Parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution)
- Software Selectable Baud Rate
- LIN Bus Monitor Mode identifies errors : Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors.
- LIN Bus Master Mode operates at same time as LIN Bus Monitor
- LIN Bus Slave simulation - with or without an LDF file
- LIN Bus hardware schedule table with support for LIN diagnostics
|
| |
|
|
CAN