Multiple Protocol Tool to Support Today’s and Tomorrow’s On and Off Highway Vehicle Bus Needs

Intrepid Control Systems introduces the neoVI YELLOW. The neoVI YELLOW fills the need for multiple CAN channels and J1708 support. It is a low cost, high value CAN and J1708 bus interface that fits in your pocket. Unlike most competing products, the neoVI-YELLOW is fully isolated from the PC and supports 100% network bus load.

Connect to Multiple CAN and J1708 Networks Simultaneously

With its two CAN channels and a J1708 channel, the neoVI YELLOW will allow you to view network traffic on all networks simultaneously with an accuracy of 10 microseconds.

Log Data to Internal Memory Card without a PC

neoVI YELLOW supports a microSD card for trouble-free datalogging. Now you can log data without your PC. Setup neoVI YELLOW - Logger including message filtering with Intrepid Control Systems’ Vehicle Spy software, disconnect from your PC and log vehicle network traffic until the card is full. neoVI YELLOW supports logging on all networks simultaneously with no latency issues.

Embedded Scripting and Automation - Function Blocks

Easily setup automated scripts such as transmitting multiple messages at a given interval and much, much more using neoVI YELLOW’s internal scripting engine. With Intrepid Control Systems’ Function Blocks, you can use an easy-to-use, mouse driven interface that creates simple yet powerful automated tasks embedded on the hardware itself.

RP1210 Support

As with all of Intrepid’s Vehicle Interface Products, the neoVI YELLOW supports both RP1210 and J2534 for standard interfaces to your applications. If you are not using a standard interface, Vehicle Spy can serve as the user interface application.

Compatible Software

• Allison DOC
• Bendix ACOM Diagnostics
• CAT Electronic Technician
• Cummins Insite
• International DLB
• International ServiceMaxx
• Meritor WABCO PC Diagnostics

neoVI YELLOW 15 PIN Connector

Physical Dimensions (with boot):

• 5 x 3 x 1.2" (12.9 x 7.6 x 3 cm)
• 5.5oz (157 g)

Device Specifications

• 2 DSPs and 1 RISC processor for 88 MIPS of processing
• 1 MB message buffer
• Power Consumption (typical) : 100mA @ 14.4 VDC
• Sleep Power Consumption (typical) : 8mA @ 12.0 VDC
• Power Supply: 5.5-32 Volt Power Operation
• Temperature Range: -40C to +85C
• Vehicle Connectors : 15 Pin male D-SUB
• General Purpose IO: 2 MISC IO (0 - 3.3V)
• General Purpose IO rate report interval: 1 Hz to 10 Khz or based on digital change
• Microsoft© Certified USB drivers
• Isolated USB 2.0 Full Speed Device backward compatible with USB1.1
• Stand-Alone Mode Including Scripting, Receive Messages, Transmit Messages, Expressions, IO, and Transport Layers
• RS232 host port with HW handshaking support for scripting and gatewaying network data
• ICS TimeSync for Multiple Hardware Synchronization supports all neoVI 3G devices
• J2534 and RP1210 A/B compatible for CAN/ISO15765, J1708, Keyword, and ISO9141
• MicroSD card slot supports up to 12 Gigabytes of storage. The removable card is formatted using FAT32 for direct usage in a PC.
• Battery backed real-time clock (RTC)
• Warranty: One Year Limited Warranty
• Firmware: Field upgradeable design (flash firmware)

Networks - General

• 64 Bit time stamping to accuracy of 10 microseconds on networks and never overflows. 0.5 microsecond accuracy timestamp available if using one network only.
• Simultaneous operations on all networks
• Transmit message double-buffering on all networks allows back to back message transmission

Network Specifications

• 2x J1939/CAN Channels
• 2 Dedicated ISO11898 Dual Wire CAN Physical Layer (TJA1040)
• CAN 2.0B Active
• Up to 1 M-Bit Software Selectable Baud Rate (auto baud capable)
• Capable of generating and detecting error frames
• Logic Analysis of CAN Waveform with 25 nanosecond resolution
• Graphical Bit Time / Baud Rate Calculator
• Listen only mode support
• Unterminated network detection

J1708

• High precision time capture of J1708 bus events
• Software selectable parameters including baud rate
• SAE J1708 Physical layer

K and L Line, 1x LIN (Local Interconnect), ISO9141, or Keyword 2000 UART Based State Machine

• Initialization Waveforms including Fast Init, Five Baud, and Custom
• Programmable Timing Parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution)Full support for LIN 1.X, 2.X and J2602
• K and L have software controlled transmit enable lines allowing many different variants of UART or ISO9141 communications including:Tx on L Rx on K (full duplex);Tx and Rx on K (half duplex);Tx on
• Socket selectable pull up resistor on both K and L lines
• Capable of Generating LIN Waveforms (Including Errors) using Dedicated Output Compare Hardware
• Software Selectable Baud Rate
• LIN Bus Monitor Mode identifies errors: Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors.
• LIN Bus Master Mode operates at same time as LIN Bus Monitor
• LIN Bus Slave simulation - with or without an LDF file
• LIN Bus hardware schedule table with support for LIN diagnostics

GM Class 2/ SAE J1850 VPW

• VPW Physical Layer capable ofTx and Rx operations in high speed modes (MC33390)
• Reception of IFR data during rx and tx
• Long Message transmit and reception for ECU flashing

• neoVI Yellow Overview & Specs (pdf)
• Help Documentation
• neoVI - DLL Documention